Please use this identifier to cite or link to this item: https://elib.utmn.ru/jspui/handle/ru-tsu/7715
Title: Влияние профиля лопасти на характеристики вихревого насоса открытого типа с открытым боковым каналом
Other Titles: The effect of blade profile on the performance of a side channel pump
Authors: Boldyrev, A. V.
Boldyrev, S. V.
Karelin, D. L.
Болдырев, А. В.
Болдырев, С. В.
Карелин, Д. Л.
Keywords: side channel pump
numerical simulation
steady turbulent flow
math-model
performance
vortex pump blades
pressure
вихревой насос открытого типа с открытым боковым каналом
численное моделирование
установившееся турбулентное течение
характеристики
лопасти вихревого насоса
напор
Issue Date: 2020
Publisher: Издательство Тюменского государственного университета
Citation: Болдырев, А. В. Влияние профиля лопасти на характеристики вихревого насоса открытого типа с открытым боковым каналом / А. В. Болдырев, С. В. Болдырев, Д. Л. Карелин. – Текст : электронный // Вестник Тюменского государственного университета. Серия: Физико-математическое моделирование. Нефть, газ, энергетика / главный редактор А. Б. Шабаров. – Тюмень : Издательство Тюменского государственного университета, 2020. – Т. 6, № 3(23). – С. 23-37.
Abstract: This article presents the results of a numerical modeling of a steady turbulent flow of an incompressible fluid in an open-type vortex pump with an open side channel, comparing the generalized simulation results with the existing experimental data. The mathematical model is based on the Reynolds-averaged Navier – Stokes and continuity equations, as well as on the equations of the two-layer Realizable k-ε turbulence model that accounts for the curvature of streamlines. The authors have estimated the grid independence of the solution and studied the influence of 14 blade profiles on the head and efficiency of the vortex pump. The solution of the model equations was achieved by the finite volume method using a sequential algorithm in three calculation areas (“feeder channel”, “blade wheel”, “open hull side channel and diverter channel”) with the evaluation of grid independence of the solution. The result of the solution between the calculated areas was transmitted at the corresponding points of the interface surfaces. The authors have studied the influence of 14 profiles of a blade on pressure and efficiency of the vortex pump: the initial profile of the blade with the installation in the wheel coaxial shaft of the ring plate of different width, the initial profile of the blade with a bevel on the discharge side, a profile in the form of an isosceles triangle, a profile in the form of a quadrangle, the initial profile with a rounded blade on the suction side, and a profile in the form of a rectangular triangle with a rounded blade on the suction side, among others. The simulation results have aided in proposing the blade profiles: in the form of a rectangle with a convex rounding of the blade on the suction side with a 10 mm radius and a right-angled triangle with a concave rounding of the blade on the suction side with a 52 mm radius and without rounding, giving a significant increase in pressure – more than 20%. Nevertheless, none of the considered cases have revealed any significant increase in the vortex pump hydraulic efficiency.
В статье представлены результаты численного моделирования установившегося турбулентного течения несжимаемой жидкости в вихревом насосе открытого типа с открытым боковым каналом и сравнение обобщенных результатов моделирования с известными экспериментальными данными. В основе математической модели использованы уравнения Навье – Стокса и неразрывности, осредненные по Рейнольдсу, а также уравнения двухслойной Realizable k-ε модели турбулентности, учитывающей кривизну линий тока. Была оценена сеточная независимость решения. Исследовано влияние 14 профилей лопасти на напор и коэффициент полезного действия вихревого насоса. Решение уравнений модели осуществлено методом конечных объемов с помощью последовательного алгоритма в трех расчетных областях («подводящий канал», «лопастное колесо», «открытый боковой канал корпуса и отводящий канал») с оценкой сеточной независимости решения. Результат решения между областями передавался в соответствующих точках интерфейсных поверхностей. Исследовано влияние 14 профилей лопасти на напор и коэффициент полезного действия вихревого насоса. По результатам моделирования предложены профили лопасти в виде прямоугольника с выпуклым скруглением лопасти на стороне всасывания радиусом 10 мм и в виде прямоугольного треугольника с вогнутым скруглением лопасти на стороне всасывания радиусом 52 мм и без скругления, дающие существенный рост напора – более 20%.
URI: https://elib.utmn.ru/jspui/handle/ru-tsu/7715
ISSN: 2411-7978
2500-3526
Source: Вестник Тюменского государственного университета. Серия: Физико-математическое моделирование. Нефть, газ, энергетика. – 2020. – Т. 6, № 3(23)
Appears in Collections:Вестник ТюмГУ: Физико-математическое моделирование. Нефть, газ, энергетика

Files in This Item:
File SizeFormat 
fizmat_2020_3_23_37.pdf2.08 MBAdobe PDFView/Open


Items in DSpace are protected by copyright, with all rights reserved, unless otherwise indicated.